Boards or Modules related to their respective descriptions. The power indicator does not change from red to green. Confirm every connector especially, A5 is connected Connect the connectors or install the lamp cover properly.
Check the connector A5 pin 14 and around them. Connect properly. Check for loose screws of lamp unit fixing. Tighten the lamp unit fixing screws 2 screws. Check IC and around them. When turn on the power, Does the rotation of each fan? Check fan connector. Then confirm the lamp lights up. If the lamp goes out approximately 10 minutes after it lights up, the cumulative usage time of it exceeds 4 hours. Check L and around them. Check R and around them. Check FL and around them.
When remote control is operated, the signal can be Replace the A-P. When remote control is operated, the signal can be Replace the R Electrical Parts Location P. Board 1. Electrical Parts Location Fan 2. Flowchart for Disassembly 2. Removal of Top Cover 2. Page Parts Location 1. Disassembly Instructions 2.
Page Removal Of Top Cover 2. Removal of Top Cover 1. Remove the Top panel. Top panel 1 Hold the top cover as shown in the diagram. Remove the A-P. Board block according to the steps 1 through 2 in the section 2. Loosen the 2 screws and remove the Lamp unit. Unscrew the 1 screw and remove the V-P. Page Removal Of L-P. Removal of L-P. Remove the Optical block according to the steps 1 through 6 in the section 2.
Unscrew the 2 screws and remove the LED cover. Unscrew the 1 screw and remove the M3-P. Remove the Analysis block according to the section 2. Unscrew the 5 screws and remove the Analysis case upper. Page Removal Of P-P. Removal of P-P. Remove the Top Cover according to the section 2. Unscrew the 3 screws and remove the Lamp house.
Page Removal Of K1-P. Unscrew the 2 screws and while pressing to shut each hook of the 2 resinous stands, remove the B-P. Board Note : B-P. B 1 The direction the Power Fan install. Resinous stands 2. Page Remonal Of M2-P. Unscrew the 2 screws and remove the K-P. Board block. Board K-P. Board block K2-P. Remonal of M1-P.
Flicker Adjustment 1. Data Transfer 1. Model Information Setup 1. Clog Sensor calibration 2. Page Flicker Adjustment 1. Defects in the ceiling mount bracket will result in falling accidents. Attach the supplied safety cable to the ceiling mount bracket to prevent the projector from falling down. Page 10 Read this first! Failure to observe this will cause burns, batteries to leak, overheat, explode or catch fire.
Do not use unspecified batteries. Do not disassemble dry cell batteries. Do not heat the batteries or place them into water or fire. Page 11 Read this first! If the power cord itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric shocks will result. When not using the projector for an extended period of time, disconnect the power plug from the wall outlet and remove the batteries from the remote control.
Page 12 This may occur due to pressure through use over a long period and may lead to poor health. Page 13 Read this first! Take proper care when disposing of the removed packaging material. Cautions when transporting Ensure that the supplied lens cover is attached when transporting. Hold the bottom of the projector when transporting. So that no keystone distortion occurs, place the projector parallel to the screen, and then install it on a flat surface so that it can project within the range of lens shift.
The code that follows KBC-L2 may differ depending on the country of purchase. Point at the remote control receiver part on the projector when using. Select a projection method suitable for the position of the projector. Page Projection Related Setting up Projection related Install the projector with reference to the figure below and the projection distance. You can adjust the display size and display position according to the screen size and screen position.
The peripheral devices must be turned off. If not provided or sold separately with each peripheral device, obtain the connection cables required for system connection in accordance with the device to be connected. If a cable that does not meet HDMI standards is used, video may be interrupted or may not be displayed.
Use the power cord included and ensure that it is fully inserted. Do not switch the main power off or remove the power cord. The confirmation message is displayed. Panasonic recommends that focus adjustment be made after 30 minutes or more have elapsed since picture display. When viewing a 3D video, keystone correction is not available. So that no keystone distortion occurs, place Page Remote Control Operation Remote control operation Remote control operation Selecting the picture mode You can switch to your desired picture mode settings.
Press The settings change as follows each time the button is pressed. Press Checks that the waveform for each of the Y- brightness , R- red , G- green , and After selecting an item, adjust the image with the buttons.
SCAN B ]. Defects in the ceiling mount bracket will result in falling accidents. Page 10 Read this first! Failure to observe this will cause burns, batteries to leak, overheat, explode or catch fire. Page 11 Read this first! If the power cord itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric shocks will result. When not using the projector for an extended period of time, disconnect the power plug from the wall outlet and remove the batteries from the remote control.
Page 12 This may occur due to pressure through use over a long period and may lead to poor health. Page 13 Read this first! Take proper care when disposing of the removed packaging material. Cautions when transporting z Ensure that the supplied lens cover is attached when transporting. Therefore, use such devices in a location far away enough from the projector so as to have no effect, or install the receiver of the device in a location that is not struck by light from the projector.
Point at the remote control receiver part on the projector when using. Select a projection method suitable for the position of the projector. Page Projection Related Setting up Projection related Install the projector with reference to the figure below and the projection distance. You can adjust the display size and display position according to the screen size and screen position. If a cable that does not meet HDMI standards is used, video may be interrupted or may not be displayed.
Use the power cord included and ensure that it is fully inserted. Power indicator 1 Connect the power cord to the projector. Attention z Using the projector while the lens cover is attached 2 Connect the power plug to an outlet. Page Projecting An Image page 32 Remove the lens shift cover.
Page Remote Control Operation Remote control operation Remote control operation Selecting the picture mode You can switch to your desired picture mode settings. Press The settings change as follows each time the button is pressed. Press Checks that the waveform for each of the Y- brightness , R- red , G- green , and In such a case, turn off Eyewear is not included with this projector. SCAN B ]. Adjusting the output level d.
The projector automatically detects the input signal but if an unstable signal is input, set the system manually. You can edit the memory name settings. The projected video may be clipped in [] some cases, but Projects at
0コメント